This is the fourth video tutorial about how to weave inkle bands on Mirrix looms.
A dear friend asked me: “Why are you spending all this time figuring out how to weave inkle bands on the Mirrix loom? You have inkle looms! ”
Yes, I do… an open sided one, a closed side one that my husband built me from upcycled pallet wood, and a mini.
And, I love them…. but, I find that the open side and mini inkle looms both kind of flop when I have one end on the desk edge and one end in my lap. This is the way that I like to weave with inkle looms, and I find the wobble/flop rather frustrating.
I really like how stable the Mirrix is when I have the lower edge in my lap and the upper edge against a workbench, table or desk.
Also, I love the precision of the tensioning on the Mirrix… those thumbscrews are sweet!
And, I also love the shedding device………. soooooooooo smooth. 😀
Besides, the Mirrix takes up sooooooooooooo little room to store it- inkle looms do take up a chunk of space in the studio!
That’s four good reasons that have made this rather challenging learning curve worthy of the time I have invested.
Here’s the video for the finishing process of weaving inkle bands on the Mirrix loom:
When you have woven your bands to the point that the warping rod is sitting on top of the loom, you will need to remove the spring:
Loosen the tension up a lot….
Lift the spring rod out of the spring.
Release the ends of the springs from the knobs.
Gently, ease the spring out of the warp strands by spreading the warp strands out slightly and pushing on the spring to disengage it.
Continue weaving until the shuttle almost can’t make it through the shed.
Weave one row.
Keep the shuttle in the shed, and place a darning or tapestry needle in the shed with the point pointing in the direction that the shuttle exits the shed.
Weave the next row, and repeat with a second darning needle.
The needles now point in opposite directions.
Weave one more row.
Cut the weft strand, and thread it into the first needle.
Pull it through, and remove the needle.
Thread the weft strand into the remaining needle and pull it through.
La de dah! you have finished your inkle band!
I always weave the tail end in a little bit more before I trim it off.
Loosen the tension wayyyyyyyyyyyyyyyyyy off, and slide the warping rod out of the loops.
Trim the ends, and pull them through the heddles.
Congratulations, you’ve woven some scrumptious new inkle bands! 🙂
Part 3 of the video tutorial series on how to weave inkle bands on Mirrix looms is about the weaving process:
Something that I learned as I trundled up my ever so steep learning curve with figuring out how to weave inkle bands on the Mirrix loom:
I started out by weaving one row on one band, putting it’s shuttle down, then picking up the second shuttle and weaving one row on the other band.
Sounds slow and clunky, doesn’t it? Well, you’re right.
The most efficient way to weave 2 bands at once is to weave as far as you can on one band, then set that shuttle aside, and weave away on the second band.
Oh… speaking of shuttles, here’s the tracing of my most favorite inkle shuttle:
I designed this one several years ago, and I love it. Works like a charm.
Here’s the video that shows the weaving process:
When you need to advance the warp, loosen the tension quite a lot.
Support the spring as you gently ooze the warp rod around and up the back of the loom.
Pat the warp strands back into the channel, and tighten up the tension again.
Remember, you do not need to have the tension as tight as when you are weaving a tapestry or beading.
You’ll find the perfect tension that suits you best.
Keep on weaving until the warp rod is sitting on top of the loom, and then check into the 4 th video in the series:
How to finish the bands.
This is the second stage of the video tutorials that I made on how to weave inkle bands on the Mirrix loom.
There are two bands on the loom, because in this video, I am working on the 16 inch loom.
When you work on the 8 inch loom, it’s okay to just weave one band at a time, as the warping bar doesn’t flop around.
But, on the 16 inch loom, you do need to either warp up 2 bands, or secure the other end of the warping bar with a cord so it will stay perfectly horizontal.
I tried weaving 3 bands at once on the 16 inch loom, and didn’t like it, as the center knobs on the shedding device got in the way.
Two bands are just great though.
AND…. if you want to weave longer bands, and have either a 12 inch or 16 inch Mirrix loom then the loom extenders will be your friend 🙂
I use a crochet hook and a weaving stick to make the heddling process go quick like a bunny.
Here’s the video tutorial:
Start by placing a piece of cardboard between the layers at the front of the loom and the back so you can’t see the warp strands at the back of the loom.
Place the shed changing device into the brackets. Unscrew the little knob that holds the heddle rod in place.
Pull the heddle rod back so it’s about half way along the warp strands.
Place the heddles onto the fingers of your non dominant hand.
Look down at the warp strands that are at the lower edge of the front of the loom.
There’s a gap between the strands that have gone in front of the warping bar and behind it.
Slip your fingers into the gap and scoot them up to the shedding device.
Slide a shed stick into the gap.
Voila! (which is how ‘walla’ is really spelled 🙂 )
You have shed one ready to heddle!
Now, slip the crochet hook behind the first warp strand, pluck a heddle off your fingers, and pull it forward.
Catch the other end of the heddle loop and place both loops on the heddle rod.
Go slowly, and be sure that both ends of the heddle loop stay politely on the heddle rod.
When you have all of the warp strands heddled, slide the heddle bar into position in the knobs, and tighten the lock nut.
Repeat the heddling process on the second set of warp strands for your other band.
Push the first set of heddles down as you rotate the shedding device.
Leave the shed stick in place, and use the crochet hook to pick up the warp strands for the other shed.
Take the warp strand from the back to the right of the one in front, and onto the hook,
take the hook over the front strand, and pick up the next strand and carry on across.
Slide the weaving stick out of the first shed, and slip it along the crochet hook to transfer the warp strands from the crochet hook to the weaving stick.
Turn the weaving stick on it’s side, and then pick up the warp strands one at a time and capture them with the heddles just as you did for the first set of warp strands.
Repeat this process for the second band.
Check your heddles carefully to make sure that they are opening the sheds properly.
Ahhhhh! a warped loom is a thing of beauty!
Attach the handle to the shedding device and adjust the tension by turning the thumbscrews.
Open the first shed, and insert a craft stick, then open the second shed and insert another craft stick.
Squish the warp strands together to establish the width of your band.
Weave one row, leaving a 6 inch/15 cm tail.
Change sheds, and weave the next row.
Pull up firmly on the tail end and weave it through the same shed.
Repeat several times until the tail end is woven in, and the band is established.
Next video: The fun part! Wheeeeeee…. weaving……
I love weaving inkle (warp face) bands.
I use in dollmaking:
Link to purchase pattern for Inkle dolls: Inkle Dolls
And, they are wonderful for trimming handwoven clothing:
Link to post that shows how to shape inkle bands to make a yoke or other shaped pieces of garments: Warp pulling
Over the years, I have also made hat bands, book marks, all kinds of jewelry, key fobs, vests, bags, bag handles, the garters for the men’s kilt hose for my son’s wedding, shawls, freeform pieces that combine inkle weaving, knitting, embroidery, spool knitting and crochet, as well as rugs.
Yep. I love inkle weaving.
So, as I have been exploring the possibilities of weaving with my Mirrix looms, I had to give inkle weaving a try.
I found that it was quite challenging at first. But, I don’t give up easily 🙂
I ended up spending waaaaaaaaaaaaaaay more hours than I should have, experimenting and obsessing over making inkle bands on the Mirrix.
Well… I finally succeeded.
Since it was so challenging, I figured that I should share what I have learned, so that other intrepid inkle weavers can leap right in, without all the trial, error and frogging that I went through!
There are definitely tricks to weaving inkle bands on the Mirrix looms, and I have made 4 videos to share those tricks.
Here’s part one of the video:
Here is the draft for the bands that I wove in the videos:
To read the draft: Each square represents one warp strand.
You can check your warping by looking at each shed to see that it has the same number of strands, in the order that they appear in the line.
You will be putting a total of 8 green strands on, followed by 4 orange strands, 3 sets of (1 orange, 1 green) for a total of 6 strands, then 4 orange strands and ending with 8 green strands.
At the top and bottom of the loom, you’ll see the full count of warp strands.
At the warping bar, the 2 sheds will be separated into their correct (we hope!) configuration for each shed.
The chart will give you bands like this:
The upper band is the band on the right hand side of the loom in videos 2 – 4.
I only used the center of the draft for it, without the green border strands.
The yarn is Lion Brand Cotton.
Setting up the loom for inkle bands is different than normal warping.
You need to have the warping bar at the front of the loom.
Tie the green yarn onto the warping bar and take it up and around the loom, just the same as if the warping bar was in the back.
You will need to cut the warp strand of color 1 to tie on color 2 at the warping bar, for EVERY color change.
It sounds insane, but this is the biggest key to making the whole inkle thing work on the Mirrix loom.
Trust me. You ~can~ twist your yarns around each other, and are welcome to, I’m sure, if that would make you happy….
BUT…. the quickest, easiest way to have problem free warping for inkle is to cut those little darlin’s and tie the knots between the colors.
Yay! Warped! Insert the spring rod into the spring to keep the warp strands locked into their notches.
This is sooooooooooo important! (yep… voice of ‘oops’ experience here 🙁 )
And in Part 2…. it’s on to the heddles.
I have a nifty, super friendly way of using a crochet hook and weaving stick to make the heddling process go like a breeze.
That’s coming up next…. so stay tuned! 🙂