Loading the content... Loading depends on your connection speed!

Tips for quick and easy heddling on Mirrix looms

Tips for quick and easy heddling on Mirrix looms

I love how easy it is to warp the Mirrix looms.
I’ve found that there are a few things that can make the process of attaching the heddles go quick as a wink.
Efficient is good!  :)

copyright Noreen Crone-Findlay

The first thing that I do, after I release the warping bar from the blocks and turn them around, is to slide a piece of cardboard or masonite between the layers of warp strands at the front of the loom and the back of the loom.
It sits there, in the middle, blocking the distracting view of those warp strands at the back of the loom. :)
Then, I use a shed stick that is at least as long as the width of the loom to pick up every other warp strand.

copyright Noreen Crone-Findlay

Then, I flip the shed stick on it’s side, with each end being supported by the shedding device blocks.
I now have 2 layers of warp strands because of this shed being open.
So, to keep the back warp strands out of view, I slide a ruler or strip of cardboard into the open shed.
Bliss! Now, I just have one set of warp strands ready for the heddles- Yay!
This makes things sooooo much easier!
I like the center brass knob of the shed changer to be as close to the exact center of the warp strands.
So, I count how many strands I need to attach to the rod, and divide that in 1/2.
I place 1/2 the heddles on 2 of my fingers, and 1/2 on the other 2 fingers.

copyright Noreen Crone-Findlay

I loosen the heddle rod and slide it along so it’s about 2 inches/5 cm from the edge of the warp strands.

copyright Noreen Crone-Findlay

Then, I reach behind the warp strand with a crochet hook, pluck a heddle off my fingers, and pull it behind the warp strand.
I catch both ends of the heddle loop and pop them onto the heddle bar. Slide the bar along as you go.
When I run out of the the first clump of heddles, I should be half way along the warp strands.
I work across , picking up all the strands, and attaching them to the heddle bar, then tighten up the little nut that holds the heddle bar in place.
Remove the shed stick and ruler, then rotate the heddle bar, sliding the heddles down the warp strands.
Turn the shed opener enough so the heddles open your first shed.

copyright Noreen Crone-Findlay

Use the shed stick to pick up the warp strands that are between the warp strands that you have just heddled.
Turn it on it’s side, insert the ruler, and repeat the process.
Check to make sure that all the heddles are securely attached to the heddle rods.
When I was making the video, one little bounder escaped, which was actually a good thing.
This allowed me to show how to capture the escapee heddle and tie it back in place.

copyright Noreen Crone-Findlay

Remove the shed stick and ruler and check the sheds, then attach the handle or treadle and Voila!
You’re ready to weave!
Here’s the video:

Happy Weaving! :D

4 Responses to Tips for quick and easy heddling on Mirrix looms

  1. Susan - Reply

    July 30, 2012 at 12:54 pm

    Oh MY,You ARE such a cleaver girl with heddles! Now see if there are any tips on handling the pesky, but oh so nice to weave,Double Heddled Beadwarp????

  2. Anonymous - Reply

    August 6, 2012 at 4:01 am

    Good to see someone else found a solution.. I did this too but fraid I don't have a way of video taping and putting it on the internet. I was getting very discouraged with the loom and finely came up with a very similar way to see the threads so I could put on the heedles.
    thanks
    Carol

  3. Noreen Crone-Findlay - Reply

    August 20, 2012 at 1:03 am

    Hi Susan
    I am sure that Elena, Claudia, and Brenda have answers to your questions about the mysteries of weaving with beads on the Mirrixes…. but I can't, as I don't have a clue!
    I love beads, but I don't weave with them on the loom (yet) :)

  4. Noreen Crone-Findlay - Reply

    August 20, 2012 at 1:04 am

    Hi Carol
    Using shed sticks, sheets of cardboard and/or masonite and rulers is such a good way of making the heddling process go smoothly, isn't it?
    I am all in favor of finding efficient and satisfying solutions to challenging tasks :)

Leave a Comment

Current ye@r *